Congratulations on owning a ViewPlus Tiger Elite or Premier braille and
tactile graphics embosser! This manual will introduce you to basic information
regarding your new embosser. The ViewPlus Technologies web site is another
resource for information on your ViewPlus embosser including examples,
tutorials and other useful downloads.
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired
operation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment
and receiver.
Connect the equipment to an outlet on a circuit
different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV
technician for help.
FCC Warning: Changes
or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
Note the following:
The use of a non-shielded interface cable with
the referenced device is prohibited.
The length of the power cord must be 3 meters
(10 feet) or less.
Compliance Statement (Canada)
This digital apparatus is in conformity with standard NMB-003 of Canada.
Cet appareil numérique est conforme à la norme NMB-003 du Canada.
Compliance Statement (Germany)
Bescheinigung des Herstellers/Importeurs: Hiermit
wird bescheinigt, dass der Drucker der
Maschinenlärminformationsverordnung 3. GSGV, 18.01.1991 entspricht: Der
höchste Schalldruckpegel beträgt 70 dB(A) oder weniger gemaß
EN27779-1991.
Compliance Statement (Europe)
Warning: This
product meets the interference requirements of EN55022. In a domestic
environment, this product may cause radio interference in which case, the user
may be required to take adequate measures.
Compliance Statement (Korea)
This apparatus complies with
CISPR22 requirements.
Waste Electrical and Electronic Equipment (WEEE)
Compliance
ViewPlus BV complies with EU Directive 2002/96 regarding WEEE recycling; upon the
conclusion of the product lifecycle, please contact ViewPlus BV concerning proper disposal.
C.
Safety Instructions
Read all of
these safety instructions before using the embosser. In addition, follow
all warnings and instructions marked on the embosser itself.
Do not place embosser on an unstable surface.
Do not place embosser near a radiator or heat source.
Do not block or cover slots and openings in the
embosser's cabinet; do not insert objects through slots.
Use only the type of power source indicated on
embosser's label.
Connect all equipment to properly grounded electrical
outlets.
Do not use frayed or damaged power cord.
The use of an extension cord with the embosser is not
recommended.
Unplug embosser before cleaning it; always clean it with
a piece of damp cloth only.
Do not spill liquid into embosser.
Except as specifically explained in the owner's manual,
do not attempt to service the embosser by yourself.
Detach the embosser from power source and refer to
qualified service personnel under the following conditions:
If the power cord or plug is
damaged.
If liquid has entered the
embosser.
If the embosser has been dropped or
the cabinet is damaged.
If the embosser does not
operate properly or exhibits a distinct change in performance.
Only adjust those controls that are covered by
the operating instructions.
D.
Specifications
ViewPlus Tiger Elite and Premier Series Embossers
Character Sets
DotsPlus
Braille - free programmable character sets
Paper Feed Method
Front-load tractor feed
Paper Width
4 to 12 inches (100 to 305 mm)
Paper Weight
Adjustable from very thin (copier type) paper to
heavy cardstock/plastic (75 to 230 g/m2)