| |
|
A. |
Toner Cartridges |
|
|
The EmFuse will display a warning message on the printer's display panel when toner is getting low. When a toner cartridge runs out, the printer will not print until the cartridge is replaced.
Additional toner cartridges can be purchased from ViewPlus. For replacement cartridges, use the following:
- Black toner cartridge, product number 150-52125304
- Cyan toner cartridge, product number 150-52125303
- Magenta toner cartridge, product number 150-52125302
- Yellow toner cartridge, product number 150-52125301
Toner cartridge packages may also be available. Please visit our website at www.viewplus.com for package availability and pricing information.
To replace a toner cartridge, first open the printer's top lid by squeezing the lid release under the handle in the center of the lid and rotating the lid upward. Note: If you have been printing, let the printer's fuser cool before reaching into the printer to replace the toner cartridge. Locate the toner cartridge you wish to replace; in order from left to right, the cartridges are cyan, magenta, yellow and then black.
Remove the new toner cartridge from the box and from the plastic bag. Save the plastic bag. Unlock the old toner cartridge by rotating the blue toner lock switch at the front of the cartridge counterclockwise until it stops. Carefully lift the old toner cartridge from the printer, place it in the plastic bag and discard it.
Shake the new toner cartridge gently, then turn it upside down and remove the white plastic tape.
Insert the new toner cartridge into the printer by lining it up with its corresponding image drum and turning it carefully right-side up as you place it into the image drum. Rotate the toner lock switch clockwise until it stops to lock the new toner cartridge into place, then close the printer lid.
|
| |
|
B. |
Image Drums |
|
|
The EmFuse will display a warning message on the printer's display
panel when an image drum is nearing the end of its life. When an image drum reaches the end of its life, the printer will stop printing until the drum is replaced.
Additional image drums can be purchased from ViewPlus. For replacement drums, use the following:
- Black image drum, product number 151-56127004
- Cyan image drum, product number 151-56127003
- Magenta image drum, product number 151-56127002
- Yellow image drum, product number 151-56127001
Image drum packages may also be available. Please visit our website at www.viewplus.com for package availability and pricing information.
To replace an image drum, first open the printer's top lid by
squeezing the lid release under the handle in the center of the lid and
rotating the lid upward. Note: If you have been printing, let the
printer's fuser cool before reaching into the printer to replace the image drum. Locate the toner cartridge for the image drum you wish to replace; in
order from left to right, the cartridges are cyan, magenta, yellow and
then black.
Remove the new image drum from the box and from the plastic
bag. Save the plastic bag. Set the new image drum on a flat, level surface like a desk. Remove the image drum and toner cartridge assembly for the image drum you wish to replace from the printer by lifting it up and then out of the printer.
Set the cartridge and drum assembly next to the new drum, oriented the same direction. Remove the orange packaging from the new image drum carefully and discard the packaging. Unlock the toner cartridge from the old drum by rotating
the blue toner lock switch at the front of the cartridge counterclockwise until
it stops. Carefully lift the toner cartridge from the old image drum and place it into the new drum, using caution not to spill the toner. Rotate the toner lock
switch clockwise until it stops to lock the toner cartridge
into place, then place the image drum and toner cartridge assembly back into the printer and close the printer lid.
Place the old image drum into the plastic bag and discard it. |
| |
|
C. |
Transfer Belt |
|
|
The EmFuse will display a warning message on the printer's display
panel when the transfer belt is nearing the end of its life. When the transfer belt reaches the end of its life, the printer will stop printing until the belt is replaced.
Additional transfer belts can be purchased from ViewPlus. The replacement belt product number i s 153-42931602. Please visit our website at www.viewplus.com for pricing information.
To replace the transfer belt, first open the printer's top lid by
squeezing the lid release under the handle in the center of the lid and
rotating the lid upward. Note: If you have been printing, let the
printer's fuser cool before reaching into the printer.
Remove all four image drum and toner cartridge assemblies from the printer by lifting each one up and out of the printer. Place them on a flat, level surface like a desk.
To remove the old transfer belt, rotate the blue transfer belt locks at the front and back of the right side of the printer (underneath the yellow image drum) counterclockwise.
Using the blue handles at the left and right sides of the transfer belt, lift the old transfer belt up and out of the printer. Remove the new transfer belt from its packaging. Orient the new transfer belt in the same direction as the old one and install it into the printer. Rotate the transfer belt locks clockwise to lock the transfer belt into place. Place the image drum and toner cartridge assemblies back in the printer and close the printer lid.
|
| |
|
D. |
Fuser |
|
|
The EmFuse will display a warning message on the printer's display
panel when the fuser is nearing the end of its life. When the fuser reaches the end of its life, the printer will stop printing until the fuser is replaced.
Additional fusers can be purchased from ViewPlus. For replacement fusers, use the following:
- Fuser (120V), product number 153-42931701
- Fuser (230V), product number 153-42931702
Please visit our website at www.viewplus.com for pricing information.
To replace the fuser, first open the printer's top lid by
squeezing the lid release under the handle in the center of the lid and
rotating the lid upward. Note: If you have been printing, let the fuser cool before reaching into the printer.
The fuser is located on the left side of the printer. To remove it, rotate the blue fuser lock clockwise until it stops to unlock it, then lift it up and out of the printer. Discard the old fuser.
Remove the new fuser from its packaging. Orient it with the blue fuser lock toward the front of the printer and lower the fuser into the printer. Lock it into place by rotating the blue fuser lock counterclockwise until it stops and close the printer lid.
|
| |
|
E. |
Waste Toner Box |
|
|
The EmFuse will display a warning message on the printer's display
panel when the waste toner box is getting full. When the box can no longer accept waste toner, the printer will stop printing until the waste toner box is replaced.
Additional waste toner boxes can be purchased from ViewPlus. For replacement boxes use product number 152-57108501. Please visit our website at www.viewplus.com for pricing information.
To replace the waste toner box, lift the printer's display panel until it is parallel with the floor. Grip the waste toner box access panel handles on both sides of the printer and rotate the panel down.
Press the blue tab at the top right of the waste toner box and rotate the box down. Remove the box from the printer.
Remove the clear plastic cap from the top right side of the waste toner box (next to the blue tab) and place it over the hole in the back of the box. Discard the waste toner box.
Remove the new waste toner box from its packaging. With the blue tab at the top right of the box, insert it bottom edge first into the printer and rotate the top edge up until it locks into place.
Rotate the access panel up until it latches into place. If desired, tilt the printer's display panel back down. |
| |
Print View
